Tarmac Driveways
Tarmac is the plain, hard-wearing choice for a drive: quick to lay, easy to patch and usually cheaper than block paving or concrete. Here's what you get for the money and where the catches are.
£60 to £100 per m²
A typical new tarmac drive, dug out and built up from scratch. This is a guide, not a quote.
Try the calculatorGet a quote
What a tarmac drive is
When people say tarmac, they nearly always mean asphalt: crushed stone held together with bitumen, laid hot and rolled flat. On a drive it goes down in two layers, a coarser binder course and a finer surface course, over a base of compacted crushed stone.
That base is where the money really goes. The ground is dug out, the stone is built back up and rolled hard, and only then does the asphalt arrive. If you are replacing a drive, the old surface has to be broken out and taken away first, which is why a replacement tends to cost £10 to £25 per m² more than starting on a lawn.
Are you thinking of laying it straight over what's there? That can work, but only on a base that is sound and level. The resurfacing guide explains how to tell.
The good and the not so good
Tarmac does a lot of things well, which is why so many British drives are surfaced with it. Here is the honest picture.
- Price. In one national set of installed prices, tarmac runs £60 to £90 per m² against £115 to £175 per m² for block paving.
- Speed. Once the base is in, the asphalt goes down quickly, so the drive is out of use for less time than most surfaces.
- Repairs. A bad patch can be cut out and relaid without lifting the whole drive.
- Heat. New tarmac can soften on hot days, and tyres turned on the spot can scuff it while it's fresh.
- Colour. It starts deep black and fades towards grey over the years.
If the look matters most to you, the surface comparison puts tarmac beside the other common surfaces.
Borders, edging and colour
Every tarmac drive needs something holding its edges, or the sides crumble and weeds find a way in. That could be a plain concrete kerb, a timber or metal edge against a lawn, or a row of block paving.
A block border is the look most people picture when they say "modern tarmac drive". It frames the black surface and gives a clean line against the house and the lawn. It's laid by hand, though, so it adds labour as well as materials.
Coloured tarmac is available too, red being the most familiar. Ask for the price difference against black in writing, and it is worth asking the contractor to show you a laid example rather than a sample in a tub, because the colour shifts once it's rolled and weathered.
Rain and the front garden rule
This is the part that catches people out. In England, surfacing more than 5 m² of a house's front garden is only permitted development if the surface is permeable or the rain drains to a lawn or border inside the property. An ordinary tarmac drive that runs onto the pavement needs planning permission (GOV.UK guidance).
In practice, most contractors solve it in one of two ways: a porous asphalt that lets water through, or a gentle fall towards a planted strip, sometimes with a channel drain. Either should be in the written quote. Our permeable tarmac page goes through the options.
Comparing quotes
Ask for at least two written prices and check they describe the same job. A good quote names the area, the depth of dig, what goes in the sub-base, both asphalt layers, the edging and what happens to the rain.
Be wary of any price given on the doorstep, and of anyone who has "tarmac left over from a job down the road". It's very important to get the firm's full name and address in writing, and to know that a contract signed at home usually comes with a 14-day right to cancel (Consumer Contracts Regulations 2013).
A typical two-car drive comes out at £2,150 to £3,600. If a quote is far below that, ask what has been left out.
Questions about tarmac drives
How much is a tarmac drive for two cars?
A space of about 6 m by 6 m (36 m²) tends to cost £2,150 to £3,600 as a new drive, outside London and the South East. That includes the dig-out and sub-base.
Can I have a tarmac drive with a block border?
Yes, and it is one of the most popular looks. The blocks act as the edging, so they do a job as well as look tidy. Expect the border to add to the price, as the blocks are laid by hand.
Will a tarmac drive need planning permission?
Only in the front garden of a house in England (or Wales) when more than 5 m² drains onto the road. A porous surface, or a fall onto a lawn or border, usually avoids it (GOV.UK).
Is tarmac the same as asphalt?
In everyday British use, yes. Most "tarmac" laid today is asphalt: stone bound together with bitumen, laid hot and rolled.
Can a tarmac drive be repaired later?
Usually more easily than most surfaces. A damaged patch can be cut out and relaid, although a new patch will look darker than the faded drive around it for a while.
More on driveway prices
- Tarmac driveway costPrices by size and the calculator.
- Resurfacing an old driveWhen a new top layer is enough, and when the base has to come up.
- Permeable tarmacPorous asphalt and the 5 m² front garden rule.
- Dropped kerb costWho gives permission, who does the work and why fees differ by council.
- Driveway cost by surfaceTarmac beside gravel, concrete and block paving, per m².
Get a quote for a tarmac drive
Three short steps: where the house is, what the drive needs, then how to reach you.
Tell us about the drive and we look for a surfacing contractor who covers your postcode. You hear the firm's name first, and nothing of yours reaches them until you agree. There is no charge to you. We are an independent introduction service and do not lay drives ourselves.
Got it. Your enquiry is with us.
Here is what happens now:
- We look for a contractor who surfaces drives around your postcode, then get in touch with the firm's name.
- Your details stay with us until you say go ahead.
- The contractor comes out, measures the drive and gives you a written price. No mailing list, no follow-up sales emails.